Observer-based tuning of two-inertia servo-drive systems with integrated SAW torque transducers

This paper proposes controller design and tuning methodologies that facilitate the rejection of periodic load-side disturbances applied to a torsional mechanical system while simultaneously compensating for the observer’s inherent phase delay. This facilitates the use of lower-bandwidth practically realizable disturbance observers. The merits of implementing full- and reduced-order observers are investigated, with the latter being implemented with a new low-cost servo-machine-integrated highband width torque-sensing device based on surface acoustic wave (SAW) technology. Specifically, the authors’ previous work based on proportional–integral–derivative (PID) and resonance ratio control (RRC) controllers (IEEE Trans. Ind. Electron., vol. 53, no. 4, pp. 1226–1237, Aug. 2006) is augmented with observer disturbance feedback. It is shown that higher-bandwidth disturbance observers are required to maximize disturbance attenuation over the low-frequency band (as well as the desired rejection frequency), thereby attenuating a wide range of possible frequencies. In such cases, therefore, it is shown that the RRC controller is the preferred solution since it can employ significantly higher observer bandwidth, when compared to PID counterparts, by virtue of reduced noise sensitivity. Furthermore, it is demonstrated that the prototype servo-machine-integrated 20-N · mSAWtorque transducer is not unduly affected by machine-generated electromagnetic noise and exhibits similar dynamic behavior as a conventional instrument inline torque transducer

Predictive control for energy management in all/more electric vehicles with multiple energy storage units

The paper describes the application of Model Predictive Control (MPC) methodologies for application to electric and hybrid-electric vehicle drive-train formats incorporating multiple energy/power sources. Particular emphasis is given to the co-ordinated management of energy flow from the multiple sources to address issues of extended vehicle range and battery life-time for all-electric drive-trains, and emissions reduction and drive-train torsional oscillations, for hybrid-electric counterparts, whilst accommodating operational constraints and, ultimately, generic non-standard driving cycles

Hybrid energy sources for electric and fuel cell vehicle propulsion

Given the energy (and hence range) and performance limitations of electro-chemical batteries, hybrid systems combining energy and power dense storage technologies have been proposed for electric vehicle propulsion. The paper will discuss the application of electro-chemical batteries, supercapacitors and fuel cells in single and hybrid source configurations for electric vehicle drive-train applications. Simulation models of energy sources are presented and used to investigate the design optimisation of electric vehicle on-board energy source in terms of energy efficiency and storage mass/volume. Results from a case study considering a typical small urban electric vehicle are presented, illustrating the benefits of hybrid energy sources in terms of system mass and vehicle range. The models and approach can be applied to other vehicles and driving regimes

High-performance control of dual-inertia servo-drive systems using low-cost integrated SAW torque transducers

Abstract—This paper provides a systematic comparative study of compensation schemes for the coordinated motion control of two-inertia mechanical systems. Specifically, classical proportional–integral (PI), proportional–integral–derivative (PID), and resonance ratio control (RRC) are considered, with an enhanced structure based on RRC, termed RRC+, being proposed. Motor-side and load-side dynamics for each control structure are identified, with the “integral of time multiplied by absolute error” performance index being employed as a benchmark metric. PID and RRC control schemes are shown to be identical from a closed-loop perspective, albeit employing different feedback sensing mechanisms. A qualitative study of the practical effects of employing each methodology shows that RRC-type structures provide preferred solutions if low-cost high-performance torque transducers can be employed, for instance, those based on surface acoustic wave tecnologies. Moreover, the extra degree of freedom afforded by both PID and RRC, as compared with the basic PI, is shown to be sufficient to simultaneously induce optimal closed-loop performance and independent selection of virtual inertia ratio. Furthermore, the proposed RRC+ scheme is subsequently shown to additionally facilitate independent assignment of closed-loop bandwidth. Summary attributes of the investigation are validated by both simulation studies and by realization of the methodologies for control of a custom-designed two-inertia system

Observer based tuning techniques and integrated SAW torque transducers for two-inertia servo-drive systems

A controller design and tuning methodology is proposed that facilitates the rejection of periodic load-side disturbances applied to a torsional mechanical system, whilst simultaneously compensating for the disturbance observer's inherent phase delay, thereby facilitating the used of lower bandwidth, practically realisable, disturbance observers. The merits of implementing both a full- and reduced order observer, is investigated, with the latter being implemented with a new low-cost, high-bandwidth torque sensing device based on surface acoustic wave technolog

Reduction of cogging torque in interior-magnet brushless machines

An investigation into the cogging torque in a four-pole interior-magnet brushless machines having either a six-slot stator and a short-pitched nonoverlapping winding or a 12-slot stator and a full-pitched overlapping winding is described. It is shown by finite-element analyses and measurements that, by appropriately defining the pole-arc to pole-pitch ratio, the optimal pole-arc to pole-pitch ratio for minimum cogging torque, which has been derived for surface-mounted magnet machines, is equally applicable to interior-magnet machines

A H2 PEM fuel cell and high energy dense battery hybrid energy source for an urban electric vehicle

Electric vehicles are set to play a prominent role in addressing the energy and environmental impact of an increasing road transport population by offering a more energy efficient and less polluting drive-train alternative to conventional internal combustion engine (ICE) vehicles. Given the energy (and hence range) and performance limitations of electro-chemical battery storage systems, hybrid systems combining energy and power dense storage technologies have been proposed for vehicle applications. The paper discusses the application of a hydrogen fuel cell as a range extender for an urban electric vehicle for which the primary energy source is provided by a high energy dense battery. A review of fuel cell systems and automotive drive-train application issues are discussed, together with an overview of the battery technology. The prototype fuel cell and battery component simulation models are presented and their performance as a combined energy/power source assessed for typical urban and sub-urban driving scenario

Care Planning and Review for Looked After Children: Fifteen Years of Slow Progress?

This Critical Commentary reviews progress in research into planning and reviewing for children in care in England and Wales since the publication of two major studies in the late 1990s (roughly coinciding with the New Labour period). It briefly considers the changing context of law, regulation and guidance and the aims and objectives of the care planning and review system. It then reviews the limited research literature available, in relation to a series of key topics. Consideration is also given to guides for children and practitioners on the subject. The commentary concludes by suggesting that this is an area in which research has failed to keep pace with changes in policy and practice, and recommends a more systematic approach

SAW torque transducers for disturbance rejection and tracking control of multi-inertia servo-drive systems

The paper proposes a resonance ratio control (RRC) technique for the coordinated motion control of multi-inertia mechanical systems, based on the measurement of shaft torque via a SAW-based torque sensor. Furthermore, a new controller structure, RRC plus disturbance feedback is proposed, which enables the controller to be designed to independently satisfy tracking and regulation performance. A tuning method for the RRC structure is given based on the ITAE index, normalized as a function of the mechanical parameters enabling a direct performance comparison between a basic proportional and integral (PI) controller. The use of a reduced-order state observer is presented to provide a dynamic estimate of the load-side disturbance torque for a multi-inertia mechanical system, with an appraisal of the composite closed-loop dynamics. It is shown that the integrated formulation of the tuning criteria enables lower bandwidth observers to be implemented with a corresponding reduction in noise and computational load. The control structures are experimentally validated via a purpose designed test facility and demonstrate significant improvement in dynamic tracking performance, whilst additionally rejecting periodic load side disturbances, a feature previously unrealisable except by other, high-gain control schemes that impose small stability margins